The receiver 17 , made of plastic with hardened steel guides, has the outstanding features of ideal dimensions, ideal receiver angle and low weight. Width Length between sights Barrel length Barrel profile Hexagonal profile with right hand twist Magazine capacity std. Mass weight -without magazine -empty mag. As the trigger is pulled further back, the trigger bar releases the firing pin by means of the connector The recoil impulse moves the slide 1 backwards. After about 3mm movement to the rear, the locking action between the barrel 2 and the slide 1 will be released, the barrel swings downwards over the locking block 22 and is retained in this position.
The slide moves back into its final position on its own. During this return travel the cartridge is pulled out of the barrel by the extractor 11 , and is then thrown out to the right via the ejector The ramp in the slide rails actuates the connector and separates it from the trigger bar. This causes the trigger bar to be raised by the trigger spring 25 and to be brought back into the path of the firing pin nose. And this happens: The trigger bar is pushed onto the safety ramp by the firing pin, The firing pin safety is brought onto engagement The firing pin is put under partial tension A round is passed out of the magazine, and The barrel is locked with the slide The weapon is again secured and ready to fire After the last round has been fired, the slide will be held in the open position by the slide stop lever Above components part numbers are referring to the exploded drawing.
Earlier supplied Recoil springs and tubes can certainly remain in use without problem. Except for the following listed components, all other components are interchangeable with the GLOCK All the safety or safety release devices function automatically.
If the weapon is allowed to drop, or if the trigger is subject to an off centre, lateral pressure, it is still impossible for a shot to be fired. This safety can only be released by the trigger being pulled by the trigger finger.
This situation offers maximum possible firing readiness combined with maximum safety for the user. This safety is only released when the trigger is pulled back.
There is no possibility in this position of the firing pin being released. The rear sight is adjustable horizontally by displacement, while, for height adjustment. The magazine is filled by each individual round being pushed into the magazine from the front, with the base of the round being pressed down first against the pressure of the magazine spring.
If using the factory supplied loading support, slip support over the magazine and place magazine on a solid surface. Hold loading support firmly and place thumb on top of loading device: Press down loading device against tension of magazine spring and, while keeping support down, insert a round as far as possible.
While pressing round downwards, slide support upwards release magazine spring and the round will slide into its rest. Repeat operation for subsequent rounds. Introduce or insert the magazine into the magazine shaft until the magazine catch engages fully.
Pull back the slide with free hand, and allow it to spring forwards into the final position. The trigger finger of the shooting hand remains outside the trigger guard. The weapon is now secured and ready to fire. After the last round has been fired, the slide remains open. Remove the empty magazine from the weapon by pushing the magazine catch Insert a new magazine and then either push the slide stop lever 27 downwards see photo , or pull the slide slightly backwards and allow it to spring forwards.
The weapon is now again secured and ready to fire. Pull slide 1 back to eject the round which is in the barrel 2. Check to ensure that there is no round in the barrel Allow the slide to spring forwards and pull the trigger into the full pulled position.
For normal cleaning, it is sufficient to dismantle the weapon into its MAIN COMPONENT PARTS slide 1 barrel 2 recoil spring assembly 3 receiver 17 magazine For maintaining and cleaning the weapon, it is recommended that the cleaning equipment provided as part of the accessories be used, together with the cleaning wadding and special gun greases and oils available from specialist dealers.
The GLOCK pistols are stripped into the main component parts in the following order: removing the magazine checking safety ensuring there is no round in the barrel pulling trigger right back removing barrel from slide.
Before the slide and the receiver are dismantled any further, attention is drawn to the safety and guarantee conditions. Removal of the slide see photo is carried out as follows: Grasp the pistol in the right or left hand in such a way that four fingers rest over the slide and the thumb rests on the rear side of the receiver.
Using the fingers draw back the slide 1 about 3mm Pull the slide lock 21 Push the slide forwards and separate it from the receiver. If the slide is drawn back too far more than 3mm , the trigger will move to the foremost forward position. The slide will then not separate from the receiver Do not use force. The trigger must first be pulled all the way back. Removal of the barrel see photo is carried out as follows: Push the recoil spring assembly 3 somewhat forwards with the thumb and raise it Take the recoil spring assembly out of the slide see photo 4.
Grasp the barrel on the barrel locking piece, push it slightly forwards, raise it and pull it backwards out of the slide. If the weapon is dismantled by the purchaser or by any third parties further than described in this users instruction, and if, as a result of inappropriate handling or incomplete reassembly, damage or malfunctions are caused, as a result of which the safety devices are rendered ineffective, then the purchaser shall forfeit ant claim to guarantee against damages thereby incurred to persons or property.
Any change to the basic construction of the weapon, in particular by the circumvention of the safety devices, is strictly prohibited for safety reasons, and precludes the use of the weapon. The following actions are not permitted on the weapon since they could lead to damage: With the weapon unloaded the trigger 26 shall not be manually brought into the foremost position and actuated. The trigger shall only be brought into its foremost position by pushing back the slide approx. With the slide removed, it is not permitted to tension and spring the firing pin 5 forward, since this could damage the firing pin safety.
The steel insert located in the cover platte 15 to the slide must not be removed. No liability whatever can be accepted if inexpertly manufactured or inexpertly filled ammunition is used. All liability whatever is excluded in the event of these instructions not being observed. Then the trigger may be pulled back. Bring back the trigger in its most forward position by cycling the slide.
The trigger safety lever integrated in trigger should then be properly engaged. When lateral pressure is applied on the trigger the safety should keep engaged, blocking the trigger movement. Failure of the trigger safety to properly engage or block indicates that it is defective.
Hold the slide in a muzzle down position and depress the firing pin safety. The tip of the firing pin should move forward and be visible protruding from the firing pin hole. Keep the firing pin safety depressed and shake the slide.
The firing pin should be distinctly heard moving freely. Draw back manually the firing pin about 0. Sports Illustrated tones of Hoops: A gaseous glock 19 gen 4 owners manual free even at the Sport of Basketball. Glock 19 gen 4 owners manual free download cancer all the use.
Here you can find product information and important safety instructions to help you get the most out of your GLOCK. Proverbial Glock perfection has come to CO2-powered airguns. This replica of the Glock 17 has quality written all over it. What makes it especially attractive is its dual system, with a rifled barrel that permits precise shooting of both pellets and 4.
Weighing just under a kilogram, this hefty pistol delivers a convincing recoil that Glock fans will really appreciate. The threaded barrel allows you to attach a compensator.
0コメント